Command Fusion Modular Controller 4 Module slots, 1xRS232, 1xDry C 2xCFLink, DIN rail.

Prijs op aanvraag

Artikelnummer
DIN-MOD4 CMF

DIN-MOD4

The CommandFusion DIN-MOD4 is a DIN-Rail mountable modular controller, capable of housing 4 modules, in any combination. You could for instance load it up with 4 IR modules, giving a total of 32 IR ports. Or perhaps 4 COM4 modules, giving a maximum of 17 RS232 ports (including the on-board RS232 port).

Information Panel

The information panel can be found on the front of the DIN-MOD4.

LEDs

  • CFLink ID LCD
    • Displays the CFLink ID assigned to the unit.
  • Power (Blue)
    • Off = Power off
    • Flashing = Booting or firmware missing
    • Solid = Power on and ready
  • CFLink Fault (Red)
    • Solid = Fault discovered on CFLink bus. Remain solid until reset.
    • Reset unit to clear CFLink fault flag and turn off LED.
  • CFLink Activity (Amber)
    • Flashing = CFLink activity is detected on the CFLink network.
  • COM Port Program Mode (Amber)
    • Solid = On-board RS232 port is in Program Mode (for communicating with CFLink devices via RS232).
  • COM Port RS232 Mode
    • Solid = On-board RS232 port is in RS232 Mode (for controlling third part RS232 devices).

Pinhole Buttons

  • Setup
    • Press to begin editing the first digit of the CFLink ID
    • Press again to change to editing the second digit of the CFLink ID
    • Press a third time to end editing the CFLink ID.
  • Up
    • When either the first or second digit of the CFLink ID is flashing, press Up to increase the digit.
  • Down
    • When either the first or second digit of the CFLink ID is flashing, press Down to decrease the digit.
  • Reset
  • COM Port
    • Press to toggle on-board RS232 Mode between Program Mode and RS232 Mode.

Module Information

Each module slot contains the following information:

  • Status/Act LEDs (Amber), 4 per module slot, each corresponding to a specific port on the module.
    • Depending what module is plugged in, these LEDs will show the status or activity of the modules ports.
    • Information such as if a relay is closed or open, when data is being sent or received to COM ports, etc.
    • For cases when a module has more than 4 ports (LRY8 module, etc), you can toggle which ports the LEDs are related to by pressing and holding any of the test buttons for that module.
  • Module Type Text
    • The module type that is detected will light up blue.
    • When the “Status/Act” LEDs are relating to ports 1-4, this text will be solidly lit up.
    • When the “Status/Act” LEDs are relating to ports 5-8, this text will slowly blink.
  • Test Buttons
    • These are for testing relay modules. Pressing and releasing the button will toggle the relay state.
    • Hold any test button for 3 seconds to change the “Status/Act” to relate to ports 5-8, then press and hold again to change back to ports 1-4.

Ports

On-Board RS232 Port

Depending what mode the RS232 port is in (indicated via the information LEDs), this port can be used for 2 things:

  1. Using RS232 to communicate with other CFLink devices on the CFLink network
  2. Communicating with third party RS232 devices such as projectors, TVs, etc

On-Board Digital Input

This dry contact digital input can be used to trigger rules in the CFLink network.

  1. Input
  2. Ground

The dual 5-pin CFLink connector is used to communicate with other CFLink devices on the network. Either connector can be used, as they are true loopthrough ports.

Pinout

  1. Isolated Ground
  2. Data +
  3. Data -
  4. Power (9-30V DC)
  5. Ground

MicroSD

The MicroSD slot is used to expand the on-board memory via MicroSD cards.

Module Slots

The 4 module slots can be used for any combination of modules.
Use a flat head screw driver (preferably plastic to avoid marking, but metal is fine too) to lever the modules out far enough to pull out the remaining amount with your fingers.
When inserting a module, make sure to insert it straight and all the way in until the latch clicks into position.
After inserting a module, you will need to reset the DIN-MOD4 before that module is detected.

Module Pinouts

You can find documentation for each module and the relevant page in our modules section.

Factory Reset

For information on how to rest your device to factory settings, see the Device Resetting Page.

Artikel document 4CommandFusion-Catalogue-2013.pdf
23CommandFusion-Diagram-Commercial-Boardroom.pdf
17CommandFusion-Diagram-Commercial-OfficeBuilding.pdf
39CommandFusion-Diagram-Residential-Whole-House.pdf
CommandFusion_DIN-MOD4_Spec-Sheet.pdf
QuickReferenceGuide-DIN-MOD4.pdf
Merk CommandFusion
BxDxH in cm 21,6 x 6 x 9cm
Gewicht in Kg 0.57kg
Constructie materiaal Kunststof
Constructie materiaal specifiek Polycarbonate
Verkrijgbare kleuren Dark grey matte finish
Connectivity Detachable, 2-pin 3.50mm terminal block for dry contact input
CF-link 2 looped, detachable 5-pin 3.81mm terminal block for CFLink BUS
RS-232 9-pin DB9 male port for RS232 control of devices; or programming mode which allows both programming and external control of the CFLink BUS devices via RS232
Micro SD slot Spring-loaded memory expansion slot
Power 9-30V DC, 24V DC regulated recommended 250mW (power supply is not included)
Slot-In Slots for modules to be installed in (sold separately, shipped with 4 blank modules)
Accessoires

Een moment gebuld a.u.b.